New Items

Product Details:

• DESICCANT DEHUMIDIFIER  especially well -suited for removing moisture from air at a low temp. & low humidity level. desiccant rotor is the heart of the dehumidifier . when the processed air passes through the rotor and dry air sent to the designated space via process fan. the moisture is absorbed by the rotor and this air throws out through reactivation fan with the help of electrical heaters or stream . the water from the processed air that has been absorbed by the rotor and the moisture air is removed by reactivation section. 

KEY FEATURES• Unit made Aluminium profile & Corner Joints• Inside sheet made of 0.5mm thickness GI• Outside sheet made of 0.5mm thickness pre-painted GI• 25mm thickness Polyurethane foam with 48kg/m3 density• Fasteners are made of Stainless Steel 304.• 200mm thick Zenco Desiccant Rotor.• High performances Desiccant Rotor• Low pressure drops.• Forward / Backward Curved blowers on Supply & Reactivation Side.• Inbuilt Control panel with humidity sensor• 25mm Thick G4 Filters on Supply & Reactivation Side.• Complete unit mounted on 100mm Base Frame made of 2mm thickness GI• Wooden Pallet, Corrugated packing, Shrink Wrap shall be provided in packing.

Additional Information:

• Delivery Time: 2-3 week
• Packaging Details: Wooden Packing inclusive

Product Details:

<sub>INDUSTRIAL DEW DESICCANT DEHUMIDIFIER -ZENCO -AD6500-DEW 

Dehumidifiers remove moisture from the air that is circulating through the unit. The resulting
reduction of relative humidity helps prevent rust, rot, mould, mildew and condensation
within the room, or other enclosed spaces where the dehumidifier is used.
The AD6500 is of the desiccant wheel type designed to dry air by passing a large volume of
air, the “process” air through a slowly rotating rotor. Desiccant Rotor is a hygroscopic material
that absorbs moisture direct from the air. As the air passes through the rotor the humidity of
the air is reduced, whilst the moisture content of the rotor is increased. A smaller volume of
air, the reactivation air, is heated by an internal heater and passes through a portion of the
rotor in the opposite direction. As this heated air passes through the rotor it will “reactivate”
it by removing the moisture content from the silica gel material. The reactivation air will leave
the humidifier as warm, moist air and must be vented to outside of the building. A Continuous circulation of the room air through the dehumidifier unit gradually reduces therelative humidity in the room.
The AD6500 dehumidifier is a robust unit designed to control the humidity in the enclosedspace in which it is placed. The casing is fabricated from 50mm thick polyurethane foam &aluminium profile and has been designed for the exacting conditions which can prevail inoffices, shops, houses, restaurants, public houses etc. It combines lightness and compactnesswith high reliability and strength. Carry handles are provide to contribute to its portability.
The dehumidifier has a single filter positioned at the air inlet and is used to clean the airentering the dehumidifier.</sub>

Additional Information:

• Delivery Time: 4 Week

Product Details:

Low Regeneration Temperature Desiccant Rotor 

Besides standard dimensions (Diameter and Thickness), non-standard rotors can be customized according to customers' requiremens, such as 50mm, 100mm and 150mm ,250

Additional Information:

• Production Capacity: 1000
• Delivery Time: 1 week
• Packaging Details: Wooden packing

Product Details:

KEY FEATURES• Unit made Aluminium profile & Corner Joints• Inside sheet made of 0.5mm thickness GI• Outside sheet made of 0.5mm thickness pre-painted GI• 25mm thickness Polyurethane foam with 48kg/m3 density• Fasteners are made of Stainless Steel 304.• 200mm thick Zenco Rotor.• High heat recovery performances.• Less space requirements.• Less self-consumed energy.• Low pressure drops.• Power for rotor drive is negligible.• Forward / Backward Curved blowers on Supply & Return Side.• Inbuilt Control panel.• 25mm Thick G4 Filters on Supply & Return Side.• Complete unit mounted on 100mm Base Frame made of 2mm thickness GI• Wooden Pallet, Corrugated packing, Shrink Wrap shall be provided in packing.

Additional Information:

• Delivery Time: 2-3 week
• Packaging Details: Wooden packing

Product Details:

Push pull exhaust fan is mainly composed of fan blade,  belt pulley, blade hub, belt, bearing, blade support, shutters, frame, protection mesh, motor, etc. It is widely used for ventilation of various types of poultry and livestock farms, agricultural greenhouse, industrial factory.

Specifications -Features: a) Compact Dimensionsb) Safety Framec) Easy Assembling and Installd) Versatility

Application 

•   Poultry, livestock farm ventilation;

• Greenhouses, mining ventilation;
• High temperature or smelly workshop;
•    Labor intensive plant, like garment factory;
•    Other factories need both ventilation and humidity, like textile mile;
•  Warehousing and logistics.

Additional Information:

• Production Capacity: 5000 Set/Sets per Month
• Delivery Time: 2-3 days .
• Packaging Details: Regular package is standard carton box package

Product Details:

KEY FEATURES 

• Unit made Aluminium profile & Corner Joints

• Inside sheet made of 0.5mm thickness GI
• Outside sheet made of 0.5mm thickness pre-painted GI
• 25mm thickness Polyurethane foam with 48kg/m3 density
• Fasteners are made of Stainless Steel 304
• 200mm thick ZENCO Rotor
• High heat recovery performances.
• Less space requirements 
• Less self-consumed energy. 
• Low pressure drops.
• Power for rotor drive is negligible. 
• Forward / Backward Curved blowers on Supply & Return Side. 
• Inbuilt Control panel. 
• 25mm Thick G4 Filters on Supply & Return Side. 
• Complete unit mounted on 70/100mm Base Frame made of 1.5-2mm thickness GI 

Wooden Pallet, Corrugated packing, Shrink Wrap shall be provided in packing.


UNIT TECHNICAL SPECIFICATION 
• Model Number: ERV1000
• Supply Air Flow Rate (CFM) 1000
• Supply Air External Static Pressure (Pa) ~100
• Return Air Rate (CFM) 1000
• Return Air External Static Pressure (Pa) ~100
• Rotor Size HRE/700/200/1.7
• Energy Effectiveness >70%
• Controller Electrical Starter panel with Remote Start /stop
• Working Temperature Range -10 to +60°C
• Maximum Unit Power (watts) 1200
• Sound Level ~70DbA
• Phase /Voltage/Hertz 1Ph/220V/50Hz

Additional Information:

• Delivery Time: Available in stock
• Packaging Details: Wooden packing

Product Details:

New formulation for an easy-to-apply, air-dry water-based, acrylic coating Heresite’s HereShield is formulated as a low-VOC direct to metal coating. It exhibits excellent corrosion resistance, UV resistance and weathering qualities, along with good adhesion to ferrous and non-ferrous metals without complex pretreatment or primers. Heresite’s HereShield air-dry coating is designed for spray application. Some of its outstanding properties are excellent durability, excellent salt fog performance, good adhesion, good film building characteristics, and flexibility. This single-component coating is typically applied on the internal and external surfaces of HVAC-R heat exchangers and related equipment

Product Details:

Fiberglass reinforced plastic (FRP) fans are specifically designed to capture, move, clean, and vent moist or corrosive air. Combining the best features of fiberglass and thermoset polymers, their composition is ideal for harsh industrial applications.

Airflow )m3/h) : 44500CMH
Voltage: 415v/50Hz
Power :1.1kw
Phase:Three phase
Diameter Blades : 50 inch
Blades Rational Speeds (RPM): 540
Net weight: 72kgDimension L x W x H: 1460 x1460 x 580 mm
Wall cut size: 1465 x 1465 x 585 mm

Additional Information:

• Production Capacity: 100
• Delivery Time: 4-5 days
• Packaging Details: Box packing

Product Details:

Fiberglass reinforced plastic (FRP) fans are specifically designed to capture, move, clean, and vent moist or corrosive air. Combining the best features of fiberglass and thermoset polymers, their composition is ideal for harsh industrial applications.
Airflow(m3/h): 29000CMH
Voltage          :415v /50Hz
Power(kw)      :0.55 kw
Diameter Blades (inch): Three phase
Blade Rotational Speeds (inch): 540
Net weight      : 50 kg
Wall cut size    : 1065 x 1065 555 mm

Product Details:

Evaporative cooling pads are designed to providemaximum cooling ,low pressure drop and reliable service. It is made from specially engineered cellulose paper that is chemically treated to resist deterioration. Our cross fluted,unequal angle pad design promotes the beneficial mixing of air and water for optimum cooling,. This unique design also functions to contunually direct more water to the air entering the face of the pad ,where the air is the hottest ,driest ,dirtest and the most intense evaporation occurs .

Additional Information:

• Production Capacity: 100
• Delivery Time: 5-6 days

Product Details:

Pedestal fans are extremely portable and lightweight. So, unlike ceiling fans, they can be moved to and fro, which means that you can keep them wherever you like and turn it by simply plugging the switch in the socket.Single speed pedestal fans primarily use a single-phase AC induction motor. The fan blade is attached to a spindle which extends into the motor. Inside the motor, there are two parts. The spindle, which ends in a free-spinning piece of magnetized iron, is known as the rotor.

Additional Information:

• Production Capacity: 1000
• Delivery Time: 6-8 days
• Packaging Details: company packing

Product Details:

Pedestal fans are extremely portable and lightweight. So, unlike ceiling fans, they can be moved to and fro, which means that you can keep them wherever you like and turn it by simply plugging the switch in the socket.Single speed pedestal fans primarily use a single-phase AC induction motor. The fan blade is attached to a spindle which extends into the motor. Inside the motor, there are two parts. The spindle, which ends in a free-spinning piece of magnetized iron, is known as the rotor.

Additional Information:

• Production Capacity: 1000
• Delivery Time: 15-20 days
• Packaging Details: corrugated box packing

Product Details:

Stone cutting cooling fan mainly consists of blade/motor/frame protect net/bracing cage/shutters.The motor drives blade to cause flow and louver window can open and close automaticallyto keep the dust from entering

Product Details:

• Catering to the diversified requirements of our clients, we are offering quality assured??Exhaust Fan??which is fabricated by the galvanized steel sheets and other required components. To ensure its salient performance and quality as per the international standards, we garnered the raw material from authentic and well-established vendors of the market. In order to gain utmost client satisfaction, this product is properly checked by our diligent professionals before finally delivering to the clients. Furthermore, it is highly appreciated by the clients owing to its high stability, high strength and greater resistance to corrosion.